English
Previous Congresses: 2000   2002   2004   2006   2008   2010   2012    E-mail Listemize Katılın
Manuscript  
Genel Bilgiler  
Kongre Merkezi  
Organizasyon Komitesi  
Uluslararası Program Komitesi  
Kongre Programı  
Özel Oturumlar  
Kapsam  
Davetli Konuşmacılar  
Önemli Tarihler  
İstanbul  
Konaklama  
Turlar  
UMTIK Hakkında  
Seminerler  
Bildiriler  
İletişim  
Linkler  
Kayıt Formu  
Soru ve Önerileriniz  
 
Organizasyon
Trion
Ana Sponsorlar
Tübitak
Ford Otosan
Renault
Hyundai
Diğer Sponsorlar
Fiat
Baykal
MIB
OAIB

1. TYPES OF PAPERS

It is expected that all papers presented in the Conference reflect novel approaches, developments, enhancements,  and results of research and application in the field of machine design and production. The papers will be evaluated based on three categories:

  1. Papers on Basic and applied research;
  2. Papers on application of Design and Production;
  3. General review papers

 

2. PAPERS STRUCTURE

Each paper should have the following structure and order:

  1. Title of the Paper: It is written in bold capital letters aligned left on one or more lines indicated on the template.
  2. Names of the Authors, E-mails and their Affiliation: Names of the Authors are written as aligned on left and last names in capitals. E-mail address is in italics. Affiliation of each author is written following a blank character after the e-mail of the author, followed by city and country.
  3. Abstract: A short description of the study no more than 100 words is given following the main heading.
  4. Keywords: Keywords identfiying the study are to be given.
  5. Main Text: The general rules are given in the next section. The volume of the paper is expected to be around 10-15 pages.
  6. Acknowledgement: The name of the Institution that supported the work may be cited following a main heading.
  7. References: The citation format and format of the cited references are given in the next section.
  8. Appendices: All additional information that is not necessary to present in the main text are given in appendices under a main heading.

3. TYPING INSTRUCTIONS

The manuscripts must be typed using one of the latest versions of MicroSoft Word editor using this template document. Template settings should not be changed at all. This guide is written in the format of a paper typed according to the rules.

 

Paragraphs

A paragraph is started at the beginning of a line without indentation and a blank line is given between successive paragraphs.

 

Headings

Main Headings: The main headings such as "ABSTRACT", "INTRODUCTION", "REFERENCES" are written in bold capitals and numbered. One blank line separates a Main Heading with the previous paragraph. Secondary Headings: The secondary headings are written in bold letters with first letter of words in capital. Subheadings: Subheadings are underlined words with beginning letter in capital. The text continues after the ":".

 

Tables

Every table is centered at the bottom of the page or at the top of the following page where it is first referred. A table heading is written on top, centered and numbered. Example:

Table 5. Temperature Profile at Different Measurements.

 

Figures/Pictures

The same rules as in Tables apply except that the figure caption is written below each figure. The text in the figures must be large enough to be legible. Any figure/picture (B/W or colored) must have high enough contrast. Colored pictures and figures will be printed in B/W format in the paper print version of the proceedings.

 

Equations

All equations are aligned left on a line with an equation number appear at the right hand-side in parentheses, "( )".

 

Page Numbers

Do not number the pages.

 

REFERENCES

The references in the text are given in capital parentheses, "[Author_Last_Name, Year_of_Publication]". The examples of writing journal articles, books, thesis, and papers, published in proceedings are given below:

 

1. Ritchie, G.S. (1983), "Nonlinear Dynamic Characteristics of Finite Journal Bearing", Trans. ASME, J. Lub. Tech., Vol.1, No.3, pp 375-376.

2. Kincaid, D. and Cheney, W., (1991), Numerical Analysis, Brooks/Cole Publ. Com., Pacific Grove, California.

3. Erda , G., (1983), "Free Vibration Analysis of Beams and Plates Using Finite Element Method", M. Sc. Thesis , METU Mech. Eng. Dept., Ankara.

4. Ulukan, L., (1984), "Konstrüksiyon Tekniği Kontrüksiyon Bilimi", Proceedings of 1st National Machine Design & Prod. Congress, Ankara, pp 1-14.

 

APPENDIX

 

SENDING MANUSCRIPTS

The manuscripts written in full agreement with the above rules are to be sent to the Organizing Committee by e-mail. Author information sheet(s) should be also attached to the e-mail.

 

 

 

 

 
 
- Umtik 2008 -